Frete Grátis em todos os produtos
### Descrição do Produto: Kit de Tampa de Válvula MITZONE com Juntas
O Kit de Tampa de Válvula MITZONE é a solução ideal para quem busca qualidade e eficiência na manutenção do motor do seu veículo. Com um design inovador e materiais duráveis, este kit foi projetado para atender aos padrões de qualidade OEM, garantindo uma longa vida útil e desempenho superior. A tampa de válvula vem pré-instalada com juntas e parafusos, facilitando o processo de reparo e assegurando uma instalação rápida e sem complicações.
#### Destaques do Produto:
– Instalação Simplificada: A tampa de válvula já vem com a junta e os parafusos, tornando o reparo do seu carro muito mais fácil.
– Material Durável: Fabricado com materiais de alta qualidade, o kit é projetado para resistir ao desgaste e atender aos padrões OEM.
– Junta Sem Costura: A junta sem costura elimina problemas de vazamento, garantindo um funcionamento eficiente do motor.
– Desempenho Superior: Com um design de alta performance, este kit ajuda seu carro a operar de forma poderosa e eficiente.
– Ótimo Custo-Benefício: Um investimento que vale a pena, oferecendo qualidade e durabilidade a um preço acessível.
#### Pacote Inclui:
– Nova Tampa de Válvula (com Válvula PCV)
– Nova Junta de Tampa de Válvula
– Novos Parafusos de Tampa de Válvula
#### Compatibilidade de Substituição:
Este kit é compatível com os seguintes modelos:
– 2013-2019 Buick Encore 1.4L
– 2014-2016 Cadillac ELR 1.4L
– 2011-2015 Chevy Cruze 1.4L
– 2016 Chevy Cruze Limited 1.4L
– 2012-2019 Chevy Sonic 1.4L
– 2015-2019 Chevy Trax 1.4L
– 2011-2015 Chevy Volt 1.4L
(Verifique a compatibilidade na descrição do produto abaixo)
#### Números OE:
– 25198498
– 55573746
– 25198877
– 25198874
– 264-968
#### Compre com Confiança:
Se você não tiver certeza sobre a compatibilidade do veículo ou se a peça falhar após a compra, entre em contato conosco e resolveremos o problema.
### Instruções de Uso:
Para instalar a Tampa de Válvula MITZONE, siga os passos abaixo:
1. Desconecte a Bateria: Sempre comece desconectando a bateria do veículo para evitar qualquer risco elétrico.
2. Remova a Tampa Antiga: Utilize uma chave de fenda para soltar os parafusos da tampa de válvula antiga e retire-a cuidadosamente.
3. Limpeza da Superfície: Limpe a superfície onde a nova junta será instalada, garantindo que não haja resíduos ou sujeira.
4. Instalação da Nova Junta: Coloque a nova junta na tampa de válvula, assegurando que esteja bem posicionada.
5. Fixação da Nova Tampa: Alinhe a nova tampa de válvula com os furos e fixe-a com os parafusos fornecidos, apertando-os de forma uniforme.
6. Reconecte a Bateria: Após a instalação, reconecte a bateria e faça uma verificação final.
### Características do Produto:
– Material: Plástico de alta resistência e borracha de silicone para a junta.
– Dimensões: Projetado para se encaixar perfeitamente nos modelos compatíveis.
– Cor: Preto, para um visual discreto e profissional.
– Durabilidade: Resistente a altas temperaturas e pressões, ideal para uso em motores de alto desempenho.
### Perguntas Frequentes (FAQ):
Pergunta: Este kit é compatível com meu veículo?
Resposta: O kit é compatível com diversos modelos, incluindo Buick Encore, Cadillac ELR, Chevy Cruze, entre outros. Verifique a lista de compatibilidade acima para confirmar.
Pergunta: A instalação é difícil?
Resposta: Não, a instalação é simples e pode ser realizada com ferramentas básicas. O kit vem com tudo que você precisa para uma instalação rápida.
Pergunta: O que fazer se houver vazamento após a instalação?
Resposta: Se você notar vazamentos, verifique se a junta está corretamente posicionada e se os parafusos estão bem apertados. Se o problema persistir, entre em contato conosco.
Pergunta: Qual é a garantia do produto?
Resposta: Oferecemos uma garantia de satisfação. Se a peça falhar após a compra, entre em contato e resolveremos o problema.
Pergunta: Posso usar este kit em um motor modificado?
Resposta: Sim, desde que o motor modificado seja compatível com os modelos listados, o kit funcionará adequadamente.
phillybingo –
Its been installed and working fine.
Highline Auto –
works well, thank you !
I13J –
2014 Chevy Cruze started whistling LOUD at the beginning of last week. At first I thought it was a part of a Rage Against the Machine song I was listening to on the radio (LOL!), but alas, it turns out it was coming from the engine compartment.
Engage: YouTube Shade tree Mechanic Mode!
A bit of google searching and YouTube browsing later, and I was able to diagnose the issue as a bad PCV valve on my 2014 Chevy Cruze LTZ. I was just brushing up near 96K miles, and apparently all the 1.4 L EcoTec engines produced by GM are destined to blow the PCV valve…not a matter of “if” but WHEN. My PCV valve had apparently had enough, so I found this product and it had great ratings and at a good value. I had heard that dealership wanted ~$100 for parts and another couple hundred (~$300) for labor, so I was determined to save the cash…
There are plenty of step-by-step videos online that show you exactly how to make this swap. If you have a decent tool set and any mechanical inclination, you CAN do this. It’s not that hard…I’d give it a 4/10 on difficulty scale. If I was doing it a 2nd time, it would probably take me less than 40 min. 1st time around it took around 1.5 hrs, but I was really taking my time, too.
A few notes of importance:
-When prying off the old cover, use a PLASTIC putty knife to free up the old seal. If you use a metal putty knife or scraper, you risk damaging the surface, which would of course lead to later oil leakage and nobody wants that.
-To give extra leverage getting the old cover off, insert the PLASTIC putty knife as far as you can, and then use a thin flathead screwdriver ON TOP of the putty knife (so you’re putting pressure on the putty knife with the screwdriver and NOT the metal flat mating surface), and gently but firmly pry upwards. That should release the seal and allow you to remove the old cover successfully.
-Wipe down the metal mating surface to remove the crankcase oil before seating the new cover & seal. I used isopropyl alcohol and paper towels to get it clean.
-Make sure to use Black RTV sealant on the seam of where the crankcase meets the timing belt area. It should be pretty evident where, because there should be the remnants of the old sealant there, which you’ll need to scrape off (with that plastic putty knife!) before applying the new black RTV.
-GET YOUR TORQUE CORRECT. The specs for this are 71 INCH LBS (not FT LBS!), which isn’t a ton of pressure – just past hand tight. Don’t guess on this, and definitely don’t over-torque it. IF YOU OVER TORQUE you’re destined for an expensive trip to the mechanic.
-Blow out the bolt holes with compressed air to get any oil runoff out of the threaded area. Oil is not compressible, and will result in you over-torqueing the bolts, leading to unequal seal and eventual oil leakage, and that expensive mechanic trip as mentioned above…
-If you need to reset the Check-Engine Light, just remove the negative cable from the battery, and go open the drivers door and press the brake pedal for 30 sec. That will drain all the stored electric energy, and reset the CEL. Make sure to follow the instructions on the dash after you start back up…the Chevy Cruze makes you roll down the drivers window and then back up (odd), but that gets everthing back to normal operating condition.
B. Billy –
Got this for Chevy Trax 1.4L Turbo, and it fits like OEM. The Trax was getting a couple different CELs, and after some research, turns out it is bad PCV valve built into the valve cover. I had to replace this AND the intake, because the root of the problem seems to be a bad valve in the intake manifold having to do with turbo boost pressures blows out the PCV valve diaphragm. After these were replace, car runs strong again, no more hesitation or excessive oil consumption. Install was pretty easy, with some basic tools it all can be done. I used the the old oil cap, this one looks too generic. It all fits like OE, and looks like OE and there are no leaks. Good product so far.
D G 31 –
Fit my 2016 buick encore 1.4 turbo perfectly. I originally intended to only replace the gasket, but opted for the set. Glad I did. I had no idea the valve cover has an internal diaphragm you can’t see that can go bad and cause a vacuum leak.
Eric Ko –
Installed and tested working good. Value for money.
Jorge Cesar Ruano Palafox –
Usable
BEE-BEAUTIFUL LLC –
Top popped off and oil went everywhere
Bill M. –
This fixed my wife’s 2016 Chevy Cruze Limited. It was actually an easy install. It came with the gasket pre-installed. I think the hardest part was prying the old one off (which really wasn’t that difficult – I just pried it off with a flat head screwdriver). I did have to re-use the old oil fill cap and funnel. That thing between the valve cover itself and the oil fill cap (I’m calling is a funnel, for lack of a better word) does come off. There’s a clip that you have to pry up a bit to get it up about 3/4″, then the funnel unscrews from the valve cover. I haven’t seen any vids that show this step, but it comes of relatively easily. No need to break it. I wish I had removed it before taking the cover off, though. Would have been easier than trying to do it one handed while trying not to get oil all over the place.
Anyway, this was one of the easiest repairs I’ve done. I’m happy, wife’s happy, all’s good.
Amazon Customer –
The part seems decent quality and fits just fine. I had an issue with the bolts being different sizes, half of them were an E-10 torque and the other half were an E-11, making install more difficult than it needed to be. Makes no sense why they would put 2 different sizes. Also, the oil cap popped off during test drive, making a huge mess.