Frete Grátis em todos os produtos
- Heavy duty 12AWG wire, better protection to the circuit.
- Wire length: 8.7 inches 12 gauge wire each side, Fuse holder dimension: 41x35x15mm
- Fits for 1A, 2A, 3A, 4A, 5A, 7.5A, 10A, 15A, 20A, 25A, 30A ATC/ATO blade fuse.
- The rubber cap fits on tightly to protect any standard blade fuse inside.
- Package included 5 x fuse holder & 5 x 30A blade fuse.
GELRHONR 10FT Cigarette Lighter Adapter to O Ring Terminal Harness,12V-24V 8mm Eyelet Terminal to Female Cigarette Lighter Socket Extension Cable with 20a Fuse for Car Inverter...
*$312.80
RED WOLF Car Stereo Wiring Harness Male Connector Adapter Replacement for Saturn 2006-2009 Ion 2006-2007 Vue Install Aftermarket Radio CD Player Receiver Cable Plug
*$325.00
Frete Grátis em todo o BrasilProduto Original Importado dos EUA
MCIGICM 12 AWG Inline Fuse Holder with 30A ATC/ATO Blade Fuse, 5 Pack
*$253.00
Informação adicional
| AC Adapter Current | 30 Amps |
|---|---|
| Brand | MCIGICM |
| Material | Plastic or Rubber |
| Mounting Type | Holder |
| UPC | 727040384197 |
Zero Signal –
I added a battery tender and a USB outlet to my motorcycle. Each one required a dedicated circuit from the battery (trying to tie into the factory fuse block would have been a nightmare).
When adding a circuit, ALWAYS add a fuse as close to the battery as you can get it. If an unfused power wire accidentally grounds itself to the frame, the best you can hope for is that it will melt in half before it sets anything nearby on fire. I’m not willing to take that risk, especially when fuse holders are inexpensive.
I bought these holders because they have a rubber cap that covers the fuse and fuse socket. Since these live under the seat of my bike (not normally hit by splashing water but not totally shielded either), it made sense to have everything covered.
I soldered and heat-shrunk all the connections, then plugged a fuse in. Everything works fine. My battery tender is on one circuit, my USB outlet on another. I put a little dielectric grease on each fuse to add an extra layer of protection against corrosion, but that’s not necessary in most cases.
It’s been about a year and both circuits are working correctly. I used a third one of these when I put an electric fuel pump on my lawn tractor, and that one also works fine. Not much to say about these except that they’re a good value and they work well.
Michael H. –
Recommended. Great product. Good Quality. Exactly as described and expected.
Fabio –
Used a couple of them on some led lights. Wire is a lot heavier than I needed for the application but doesn’t matter to me I’d rather have over kill. And i’v got a couple left so the next project I might be happy for the heavy wire.
Keith Norwood –
Solid product, confident that it’s water proof/resistant. Really only needed one, but I’m glad I got a pack since I have other projects that will need them as well.
travis –
Excelente producto
Michael P. –
The turret lights went out on our hospital security car. Usually I swap a fuse under the hood but the single box was corroded. To buy 1 at a local store was $17.00. So I bought this 5 pack with 30A fuses. Spliced it in and lights work fine now. Now we have extra plus fuses to match.
CSB –
This was perfect, to spec, good quality wire, case and insulation.
Cheapest insurance ever when messing with high power batteries and DYI wiring.
I used it to wire a XT90 connector near my car battery where I can plug accessories such as two SUP air pumps at the same time without stressing the car wiring and lighter outlets.
Used an extra one for the backup Lipo.
CSB –
The media could not be loaded.
I only have these inline fuses four out of five stars only because the wires are thicker than the switch wires and light wires. Other than that they work great and was an easy install. I installed them on the open terminals of each switch and then connected the lights to the inline fuses.
David mark strauch –
excellent product, very happy with my purchase
Fabio –
Liked these products. Used on my Polaris Ranger. Worked wel