Frete Grátis em todos os produtos
- Saves money – this fuel tank roll over valve allows direct replacement of only a failed valve, rather than the entire tank
- Upgraded material – aluminum construction prevents similar failures from original plastic design
- Easy installation – 2 washers, 1 gasket, 1 threaded fastener and 1 installation wire included
- Application specific – made to replace the original valve on certain Chevrolet and GMC vehicles
- Ensure fit – to make sure this part fits your exact vehicle, input your make, model and trim level into the Amazon Garage
18-7212 Carburetor Rebuild Kit, 1395-97611 1395-9725 Gasket and Diaphragm Kit，Replacement for Mercury or Mariner 6, 8, 9.9, 10, 15, 20 and 25 HP 2cyl, 1395-811357, 1395-9179,...
*$337.00
JEENDA Fuel Pump Sender Unit 5C3Z-9275-BA 5C3Z9275BA Compatible with Ford F250 F350,F-250 F-350 Super Duty 6.0L 2003-2007
*$673.00
Frete Grátis em todo o BrasilProduto Original Importado dos EUA
Dorman 577-106 Fuel Filler Neck Inlet Check Valve Compatible with Select Chevrolet/GMC Models (OE FIX)
*$1,521.30
Informação adicional
| Material | Aluminum |
|---|---|
| Brand | Dorman |
| Item dimensions L x W x H | 4.5 x 2.75 x 1.5 inches |
| Exterior Finish | Machined |
| Inlet Connection Type | threaded |
| Global Trade Identification Number | 00885484843448 |
| Manufacturer | Dorman Products |
| UPC | 885484843448 |
| Item Weight | 1.44 ounces |
| Product Dimensions | 4.5 x 2.75 x 1.5 inches |
| Country of Origin | China |
| Item model number | 577-106 |
| Manufacturer Part Number | 577-106 |
| OEM Part Number | 15053176, 15053177, 15105259, 15174292, 15181557, 15229310 |
| Date First Available | January 5, 2018 |
eric b –
Mechanic resolved leak with thus after market tank/ neck replacement.
OG –
Good part recommend this 100%
Matthew Hamilton –
Worked as designed
us army ltc 05 –
This is the only filler neck repair repalr kit that works by desighn the flapper door is not to stiff like on some others and or resticted flow if you want your filler neck fix right the first time then get this one also be very carefull to only cut on the outside of the old failing filler neck just above where its leaking as to not make your whole to big cut only on the outside of the tank and take your time. 2004 GMC envoy your good to go.
Z.K. –
Works on a 08 h2 gas tank
Make sure you sanding well the surface to make it flat and flush or you won’t get a goo seal at the top when you tighten it
David –
فوهة خزان وقود مناسب للهمر H2
Z.K. –
When I installed the item, which involves the removal of the fuel tank and the fuel pump, the seal would not fit properly even though I was following the instructions exactly. I called the Dorman Tech Assist line and was informed that the instructions that came with my kit (revision 2016) were wrong and had been updated with revision 2018 that completely changed where the rubber gasket was to be installed. A pic of the revised directions that are available on Dormans website in pdf form is attached to this review as well as a shot of the directions that came with the kit. I had to take the fuel pump back out and reinstall with the rubber gasket now on the inside where it fit neatly into a groove on the valve and sealed up. If you failed to catch this and installed it the way the instructions that came with it said then you would have a leak and set potential code P0440. Other than that it fit good and worked good on my daughters 2003 Chevrolet Trailblazer LT 4.2L that the fuel fill neck cracked off of the tank. There are some good youtube videos out there to reference for the job.
eric b –
An intellectually challanged individual had previously attempted to repair the leaking Fuel Filler Neck Inlet following a youtube video made by another such person not only endangering the lives of anyone riding in the vehicle but also failing to stop the leak, before I bought the vehicle.
Once I cleaned that mess up this item worked perfectly.
Breanna U. –
I had the plastic neck on my 2006 Jeep wrangler gas tank snap off. (The plastic gets brittle with age) so I drilled the hole out a little bigger 1.5 inches and installed this filler neck. It installed tight and seals up tight so it should work great! Very happy to not spend $500 on a new tank, with plastic parts. I used a step drill bit to drill the hole in the fuel tank and it worked great! So buy one that goes to at least 1.5 inches. Then smooth outer edge and done. Took me all of 10 minutes start to finish.