Frete Grátis em todos os produtos
- Replace Part #12223861 / 16040749 / 12223749; Fits for GM Buick GMC Chevrolet
- Map sensor range – 3 Bar; Map Sensor range PSI- 44psi
- High performance MAP sensor, meets or exceeds OEM standards, 100% tested before shipping
- The pictures are accurate because of real shooting, please check it carefully to make sure it is what you need; And please double check the part number of your item, matching information is for reference only
- Kindly do not hesitate to contact us back in the future if you feel that you need further assistance
Set of 4 ABS Wheel Speed Sensor Front Rear Left/Right Compatible with E90 E91 325xi 328xi 335i xDrive 34526764859 34526764858
*$708.90
Denso 234-4127 Oxygen Sensor
*
Frete Grátis em todo o BrasilProduto Original Importado dos EUA
3 BAR MAP Sensor For Various GM Models with Connector Pigtail
*$373.00
Informação adicional
| Brand | BLUE ELF |
|---|---|
| Item dimensions L x W x H | 2 x 2 x 3 inches |
| Mounting Type | Flange Mount |
| Output Type | Push-Pull |
| Specific Uses For Product | automotive repair, maintenance, or modification |
| Manufacturer | BLUE ELF |
| Style | Modern |
| Item Weight | 1.76 ounces |
| Product Dimensions | 2 x 2 x 3 inches |
| Item model number | 12223861 |
| Manufacturer Part Number | BEYWM345 |
| Date First Available | June 27, 2019 |
J.S. –
Absolute garbage, save your money and just buy a genuine sensor. HPT shows that readings are erratic and incorrect, even with correct scaling for a GM 3bar map sensor. Car would barely idle and die as soon as any throttle was applied. Replaced this garbage with one from a known good company and all the problems went away. This part reading incorrectly could absolutely destroy your engine, do not take the risk and just buy something better quality.
Michael –
Using this to send my data to a FAST system on my turbo car it works just fine.
Fred –
Not what promisse
Raptor Rob –
The pins of the supplied connector don’t fit in with of the sensors I purchased. I had to de-pin the connector and force them into the sockets. Then I could reassemble and install. After reading the reviews I think I’m just going to return them.
Update, I moved it up to three stars. I was able to get the connector to work and tested the two units. Both sensors supplied the correct voltage for the vacuum I supplied.
C. Holten –
Pig tail it comes with is trash and doesn’t even fit properly! And the sensor itself was just a piece of plastic with pins! Installed and truck wouldn’t run properly, pulled it off and looked, turns out it was molded plastic!
Can’t give 0 stars for review, so 1 it is!
96 chevy s-10
Owen”O”Windham –
3 pins in sensor were drill too small pigtail supplied or oem does not fit in sensor.
Using a 2.40 mm drill bit i’ve enlarged 3 holes for both oem and pigtail supplied would fit.
Very disappointing quality control
Clarence –
Plug will not fit into the map sensor so I use the old plug with the new map sensor truck kept dying but it only cost me like $4 probably why they’re $40 everywhere else but Amazon had it on my porch just like always and right on time
tci express luis monzon –
Do not buy I got a 1 bar when I ordered a 3 bar.
Raptor Rob –
Tried to use this on a twin turbo Coyote setup with Holley HP Efi. Engine would backfire and start running lean. Looked at the data log (pictured) and saw the MAP value erratic and capping at 100kpa. No Bueno. Why advertise 3 bar and sell a 1 bar unit? That’s how engines get destroyed. Steer clear of this trash…
J.S. –
I’ve used this on a single turbo LS swap. The reading on HP tuners is slightly off from what it actually is.